欧美日韩首页_成人一区二区在线观看视频_91大神在线免费观看_成人午夜免费福利_久久网一区_9久精品

歡迎來到東莞市艾維品實業有限公司官網!

東莞市艾維品實業有限公司

專業研發、生產、銷售各種花紋的水轉印膜

全國咨詢熱線

400-0253-888

新聞資訊

新聞中心

當前位置: 首頁 > 新聞中心 > 三沙公司新聞

聯系我們Contact Us

東莞市艾維品實業有限公司

聯系人: 董先生/Abe Dong

手 機:13378609888

 箱:dgivip@163.com

 址:廣東省東莞市樟木頭鎮金河社區濱河路31號

網 址:m.junshiaihao.cn

三沙水轉印加工技術操作方法

2023-06-02 09:02:52

1. 確定適當水溫 (20 °C – 30°C),水面保持溢流狀態。

Make sure the proper water temperature (20 °C - 30 °C), keep water at overflow state.


2. 保持水表面無活化劑殘留及雜質。

Keep the water surface without activator residues and impurities.


3. 置膜,以適當角度將膜平放于水面(確定膜之正反面,印刷層朝上)

Put the film on the water flatly with the proper angle.( Confirm the film positive & negative, printing side up)


4.配合水溫設定溶解時間,水溫一般為25-30度,溶解時間約為45秒到2分鐘

Set dissolution time with water temperature which is often 25°C-30 °C. The dissolution time is about 45 seconds to 2 minutes.


5.視印刷油墨之厚度,判定噴涂活化劑之時間,油墨層越厚,可在膜尚未完全溶解時,提前噴涂活化劑,讓油墨活化時間加長,而一般作業情況溶解1分鐘左右可噴涂活化劑,待膜成鏡面而平坦擴展(5秒-15秒)即可上膜、轉印。

Spray activator time depends on the thick of printing ink. The thicker the ink layer, spray activator in advance before the film not yet completely dissolved, to make the ink activate time much longer. General operation condition is about 1 minute to dissolve, then spray activator. After flat extension of the film (5 seconds -15 seconds), then put the film to be printed and transferred .


6. 在上膜之前需視加工物之外形或有紋路性,選擇下水角度,以利于空氣排出。

Select water down angle to exhaust air well as the dip items' shape or lines prior to film transfer . 


7. 上膜后,不可立即拿起,應在水中搖晃3-5秒,切斷邊緣之膜,增加紋路咬住被加工物之時間。

Do not take out the work piece immediately after transfer the film. Shake it on the water for 3-5 seconds, to cut the edge's film and increase the lines to bite work piece's time.


8. 活化劑噴涂需以0.8mm*4孔噴槍及可攪拌式壓力操作業,噴涂距離約30cm,空氣壓力適當調整避免花紋脫落,不可有水花產生,必要時水溫可加到35°C, 水槽之水量需作溢, 最后一道水需干凈,沖洗完成需經空氣吹干并經品管修整再入烘烤爐。

Spray activator with 0.8mm * 4 hole spray gun and operate by stirred pressure. Spray distance is about 30cm. Adjust air pressure properly to avoid the film pattern fall off, and water can't be splashed. Add water temperature to 35 °C if necessary. The tank water is overflow and the last water must be clean. After rinse, then dry by oven. 


不同的圖案,必須使用不同的底色,如木紋基本使用棕色、咖啡色、土黃色等,石紋基本使用白色等.

 Different film pattern , different base coat. e.g. Wood grain (often Brown, khaki), Marble grain (often white etc).


近期瀏覽:

相關產品

相關新聞

contact us

東莞市艾維品實業有限公司

廣東省東莞市樟木頭鎮金河社區濱河路31號

水轉印膜丨水轉印耗材丨水轉印設備

水轉印產品代加工丨水轉印技術支持

水轉印開發、生產、加工、銷售、培訓一條龍服務

contact us

         


         掃一掃 添加微信

SERVICE

聯系人:(董先生)

133-7860-9888

全國熱線

400-0253-888

座機

0769-81723888

0769-87123588

24小時在線客服
主站蜘蛛池模板: 一本之道无码一区二区 | 亚洲欧洲精品一区二区精品久久久 | 黄片毛片在线 | 韩国中文字幕在线观看 | 欧美成人精品欧美一级乱黄 | 女人天天干夜夜爽视频 | 伊人网视频在线观看 | 国产素人在线观看 | 国产精品视频123 | 九九久久这里只有精品 | av无码一区二区三区午夜 | 亚洲精品成人片在线观看精品字幕 | 久久婷婷日日澡天天添 | 国产精品久久一区二区三区不卡 | 亚洲国产一区二区三区在线观看 | 国产精品久久久久久妇女6080 | 久艹av| 99久久99久久精品免费 | 噜噜噜狠狠夜夜躁精品仙踩林 | 久久久www成人免费精品 | 成熟丰满熟妇xxxxx | 美女视频黄频免费观看a | 国产麻豆亚洲精品一区二区 | 久久密av| 国产在线精品一区二区中文 | 伊人久久一区二区三区小说 | 色婷婷一区 | 91亚洲国产成人久久精品网站 | 国产黄a三级三级三级av在线看 | 美国黄色毛片女人性生活片 | 日韩精品高清自在线等信息 | 99re热国产| 免费一级肉体全黄毛片高清 | 狠狠色噜噜狠狠狠888米奇视频 | 天天草夜夜爽 | 在线观看视频网站www色 | 久久久久久免费视频 | 吃奶做受在线播放 | 狠狠色丁香久久综合婷婷 | 国产精品成人影院在线 | 欧美成人理论片乱 |